故障
Malfunction | 原因
Causes | 措施
Measures |
在减速机的紧固件处有大的噪声
High noise at tightening parts | 紧固件松动了
Loose of tightening parts | 将螺栓/螺母拧紧到规定的扭矩。更换损坏了的螺栓/螺母。
Tighten nut bolt to correct state Replace damaged nut/bolt |
减速机的噪声变化
Changing noise | 齿轮的轮齿发生了损坏
Teeth of gears get damaged | 和客户服务部联系。检查所有零件上的齿，更换损坏了的零件。
Consult after-sales department
Check teeth of gears and replace damaged one. |
轴承间隙过大
Clearance of bearings too big | 和售后服务部联系。
调整轴承的间隙。
Consult after-sales department
Adjust the clearance of bearings |
轴承损坏
Bearings get damaged | 和客户服务部联系。
更换损坏的轴承。
Consult after-sales department
Replace damaged bearings |
轴承温度升高
Bearing temperature rise | 箱体里面的油面过高或过低
Oillevel is too high or low | 在室温下检查油面的高度并按需加油。
Check oil level at room temperature and add on reduce oil |
油过于陈旧
Oil is used too long | 和售后服务部联系。
检查上次换油的时间。
Consult after-sales department.
Check the date that oil be replaced last time. |
油泵的机械故障
Malfunction of oil pump | 和售后服务部联系。
检查油泵的工作是否正常，修理或换新的油泵。
Consult after-sales department.
Check if pump works normally,repair or replace it. |
轴承损坏
Bearing damage | 和售后服务部联系。
-查阅操作人员在振动测量中所获得的数据。
-检查并按需要换轴承。
Consult after-sales department.
-Look up the date about vibration.
-Check and replace it on request. |
工作温度过高
Working temperature too high | 箱体里面的油面过高
Oil level is too high | 检查油面的高度，如果有必要的话，调整。
Check oil level,and adjust if necessary. |
油过于陈旧
Oil is used too long | 和售后服务部联系。
检查上一次换油的时间，如果有必要的话就更换。
Consult after-sales department.
Check the date that oil was replaced last time,
replace it if necessary |
油受到严重污染
Oil is pollucted seriously | 和售后服务部联系
-换油。
Consult after-sales department.
-Replace oil. |
在配备了润滑油冷却系统的减速机上：冷却剂的流量过低或者过高
Flux of cooling material is too high or low | 全面调节进口和出口管道的阀门。
检查水冷装置的自由流量。
Adjust entrance and exit valves.
Check the flux of water cooling devices. |
通过水冷装置的油流过低，其原因是：滤油器严重堵塞
Oil flux through water cooling devices is too low | 清理滤油器
Clean oil filter |
油泵的机械故障
油泵损坏
Malfunction of oil pump
Oil pump damage | 和售后服务部联系。
-检查油泵的功能是否正常。
-修理或者换新。
Consult after-sales department.
-Check of oil pump works normally.
-Repair or replace it. |
在配备了风扇的减速机上：风扇罩的空气入口和/或箱体严重污染
Entrance of fan shield and housing polluted seriously | 清理风扇罩和箱体
Cleanse fan shield and housing. |
配备了冷却螺旋管的减速机：冷却螺旋管里面结垢
Redsidues in cooling coil | 和售后服务部联系。
-清理或者更换螺旋管。
Consult after-sales department.
-Claen or replace cooling coil. |
轴承处的振幅升高
Swing at bearing higher | 轴承损坏
Bearing is damaged | 和售后服务部联系。
-检查并按需更换轴承。
Consult after-sales department
-Check and replace bearing. |
齿轮损坏
Gear is damaged | 和售后服务部联系。
-检查并按需更换齿轮。
Consult after-sales department.
-Check and replaces gears. |
止回装置的温度过高
止回功能的失效
Temperature of anti-backstop too high and it becomes malfunction | 止回装置损坏
Anti-backstop becomes malfunction | 和售后服务部联系。
-检查并按需更换止回装置。
Consult after-sales department.
-Replace anti-backstop |
减速机漏油
Oil-leak of gear unit | 箱体盖或者联接处的密封不良
Sealing at cover and connection not in good state | 检查密封和连接处，如果必要的话，更换新的。将连接处密封好。
Check air-proof and connection part,replace them if necessary,and seal up connection part. |
径向轴封失效
Shaft seal is malfunction | 和售后服务部联系。
-换新的径向密封环。
Consult after-sales department. |
油中有水
Water in oil | 油中有杂物
Mixer in oil | 用试管检查油的状态是否有水分存在。
实验室分析油.
Classify if there is water in oil by using tube.
Analyse oil in laboratory. |
润滑油冷却器或者冷却螺旋管失效。
Cooling coil is of mal-fanction | 和售后服务部联系。
-找出并修理泄漏之处。
-更换冷却器或者螺旋管。
Consult after-sales department.
-Find out and repair leakage place.
-replace cooling coil |
减速机受到机器间通风过来的凉空气而产生凝露
Cool air will cause water drop in gear unit. | 用合适的保温材料将减速机保护起来。
关闭空气的出口或者在结构上改变其方向。
Shelter gear units with proper |
关注官方微信
